How to Take Runs Out of Bathworks Tub Refinisher
Then, you're wondering how to paint your bathtub properly. Well, you lot've come to the correct place, as we've been refinishing tubs professionally since 1972. Maybe you're but considering whether or not this is a weekend projection you want to tackle? Or maybe you've already purchased a Bathworks® DIY kit for your bathtub, and are looking to get started. Regardless, you've come to the right identify. I'yard going to tell y'all how to do it the best and easiest way, just similar a pro!
Let's Become Started (Estimated Prep Time: 45 minutes)
The get-go thing to exercise is remove all items (your tooth brush, shower drapery, towels, soaps, shampoo bottles, razors, etc… whatever you go on in your tub area). Next, if y'all have caulk you want to remove, now's the time to do it. Use a new razor bract, and advisedly cut along the top and bottom of the caulk – in a perfect world it volition pull right off for you.
Now information technology's time to clean. Whether you lot have a bandage iron, steel, fiberglass, or plastic bathtub, tub/shower unit, sink, shower stall, shower basin, etc… dump on plenty of Ajax or Comet cleaner and scrub! Pay special attending to any heavy lather scum areas. While the tub is still wet, scrub it once more using the Etching Cleaner provided. Note: if you take a cast iron or steel bathtub I would for highly recommend using theBathworks® EZ-Etch product (this will ensure the all-time possible adhesion with theBathworks® bathtub refinishing pigment). With the surface still moisture, sand the entire tub with 120 dust sandpaper (provided in some of our kits). Dry the tub.
At this bespeak the tub should be dry, the caulk removed, and all debris should be cleaned up and in a garbage purse. Examine the whole tub again. If you think soap residue or grime of whatsoever kind yet remains, use that same razor blade and carefully scrape it off, then scrub that surface area once more with the same cleaning process as earlier. Dry the tub once more.
Masking & Final Tack Rag (Estimated time: thirty minutes)
Ok, you're done with the h2o, and so now would be a practiced time to place a plastic bag over the tub spout and shower caput to avert any dripping. Thoroughly dry again if needed (any wet at all can forestall proper bonding of theBathworks® tub refinishing paint). Adjacent, use blue painter's record, (I like to utilise the 2" broad tape) to mask the edge of the bathtub, tape off the drain, and if the overflow is left on, you'll want to tape that likewise. Place newspaper or a tarp on the floor in front of the bathtub, as you lot'll want to make sure that no material lands on the floor surface. This is too a good spot to identify the paint tray while rolling. Next, you're going to wipe everything out one concluding time, and and then use a tack rag (provided in some kits) to clean up any remain droppings that might be on the surface of the tub.
Priming the Surface (Estimated time: xv minutes)
Alright, everything is now cleaned, dried and yous're ready to wipe on the Liquid Primer provided in theBathworks® kit. At this betoken you should be wearing rubber gloves and have good airflow (positive air coming in and the negative air going out). Cascade the primer onto the lesser of the bathtub and wipe the unabridged tub surface (I similar to use a textile, but a newspaper towel works as well). While y'all're letting the primer dry out for 5 or ten minutes, become ahead and mix upward the Part A & Role B paints and hardener provided in yourBathworks® bathtub refinishing kit. With everything mixed, yous should be ready to roll. Once more, wear gloves, goggles, and have good positive air flow.
Painting (Estimated Fourth dimension: 1.five hours.)
First, the Non-slip (optional, but I recommend it for safety). Pour the container of non-slip material (see mixing instructions included in each kit) in the heart of the tub and utilize the 3" roller (provided in some kits) to roll out a rectangle shape in your desired not-slip area. What's important virtually this footstep, is that the materials is mixed well, and while rolling you lot remember to coil in both horizontal and vertical directions, leaving the non-skid area evenly rolled. Let that sit for about 10 to xv minutes before starting to gyre the bathtub with the refinishing paint.
Next, pour the mixed Part A & B into the pigment tray (provided with some kits). With a four" foam roller (provided in some kits), start rolling on the inside wall front corner. Remember, at this bespeak the first few roller passes will not get very far, equally your roller isn't yet loaded with pigment. Be certain that y'all NEVER dry scroll (always make certain that your roller has enough of paint). I like to work my way around the inside walls and lower curve, e'er with a good amount of material on my roller. Then, I gyre the acme edge of the bathtub, leaving the forepart top deck for last. Over again, I always have a proficient corporeality of material on my roller. If you lot start to discover whatsoever runs or puddles from consistently having a lot of material on your roller, at present would be a expert time to curlicue them out.
Next, I curlicue the lesser (aye, over the non-slip expanse too), connecting the lower bend textile with the bottom material. Then I roll the "forepart" upper deck evenly, and with a skillful amount of material. Finally roll the front end of the tub.
Lastly, using a foam brush (provided in some kits) dab whatsoever areas the roller couldn't attain. At this stage I adopt to utilise our Preval Kit, rather than the brush.
Click here if you lot would similar to see what the Preval Kit is.
Using the Preval, immediately after rolling, I spray the lower dorsum curve as well as the caulk areas and front upper deck. Doing this helps lay-down the rolled textile and achieves a very smooth, professional look every time! After about thirty to 45 minutes, I'll remove all the tape pulling at a 45-degree bending. Y'all should be able to caulk and replace anything that was removed after 24 hours.
Please keep in mind that we have great tech support, and so don't hesitate to contact us. If you follow these few steps, and utilise my tips, yous'll be able to achieve a beautiful new tub for many years to come.
Happy Rock'north Rolling!!
– Craig Munro
Source: https://www.bath-works.net/how-to-refinish-a-bathtub-yourself-properly/
0 Response to "How to Take Runs Out of Bathworks Tub Refinisher"
Post a Comment